Page 1 of 1
How could I HOLD the last frame of the video?
Posted: Wed Nov 20, 2024 11:16 pm
by dfleming
Hello,
Here is what is happening:
I have setup QLC+ to have a chaser with several videos set to "HOLD INFINITE", however on the last frame of the video instead of holding the last frame it just closes the video.
What I want to happen:
I want the last frame of each video to still be visible until I click NEXT on the cue list.
Ideas?
I am trying to avoid using OSC to connect with my existing powerpoint. I would like to just use QLC+ for my video, audio, and lighting cues.
Re: How could I HOLD the last frame of the video?
Posted: Thu Nov 21, 2024 9:20 am
by GGGss
A quick and dirty solution: capture the video's last frame and add these images in the next step to your chaser. Set the timing to infinite, and you will have control of the timing now.
Re: How could I HOLD the last frame of the video?
Posted: Thu Nov 21, 2024 12:28 pm
by dfleming
Thanks! I couldn't easily import an image and don't want to use RGB Matrix to do so. I will try looping a short video with just the last frame repeated. Too bad we have to use workarounds. It feels like QLC+ is so close to being an all-in-one controller.
Re: How could I HOLD the last frame of the video?
Posted: Thu Nov 21, 2024 3:48 pm
by kenact
If you are editing the video yourself, I would copy the last frame, and extend that beyond where you think you need it. You won't be able to fade the video except at the end.
Re: How could I HOLD the last frame of the video?
Posted: Fri Nov 22, 2024 6:48 am
by thibaultphil
Good morning,
I used VLC launched by QLC+ in the past. In the VLC interface settings, check the box: pause on the last image of a video
Re: How could I HOLD the last frame of the video?
Posted: Fri Nov 22, 2024 7:12 pm
by kenact
Another possibility, set the step duration to the exact length of the video, and use the pause button to pause it near the end, then un-pause it when you're ready to continue.
Re: How could I HOLD the last frame of the video?
Posted: Wed Nov 27, 2024 11:15 pm
by dfleming
Hi all,
So in summary, can we confirm that QLC+ 4 does not play videos and respect the hold the last frame with the inifinite setting? It seems even with MP4 or WMV, the video window closes after the video plays.
Work arounds I have tried:
- importing an image to show after the last frame of video. (result: no option to import an image except for rgb matrix. I just want to project to my external video monitor on the stage)
- looping the enxt cue as a video which contains a few milliseconds of the last frame of the previous video. RESULT: the looped video holds infinitely, but now I have a new problem.
I see a black gap between my video cues. You can see my demo here:
https://youtu.be/3ok1y1z39TY
Any solutions we know of? I really hope video playback could be seamless and simple in QLC+ so I could avoid more complex solutions like using QLC+ AND an external video player like PowerPoint connected through Companion.
Re: How could I HOLD the last frame of the video?
Posted: Thu Nov 28, 2024 7:48 am
by mcallegari
QLC+ has a limited audio/video support.
For specific results I recommend to use other softwares dedicated to A/V playback.
Perhaps with Qt6 the situation will improve but right now it is what it is. Sorry
Re: How could I HOLD the last frame of the video?
Posted: Thu Nov 28, 2024 9:56 am
by GGGss
To the OP: I investigated in OBS studio. I had excellent results even in hybrid conference configuration. This was to get PPT, and static and live video feeds and ambient lighting config. This was a corporate production where budgets were present—estimated workload: 5 full days prep + production day.