Page 1 of 1
Osc input not receiving
Posted: Mon Jun 27, 2022 2:29 pm
by SPS
I have setup universe 5 for handling osc input.
The port is set to 7704 ( by default) on 127.0.0.1
When I send a osc command to this port, no packets received.
However, the osc monitor which I use (kamperman utility) registers the osc command send on port 7704.
What can be the problem?
Sending osc from qlc works good….
Thanks for your help.
Paul
Windows 11
QLC 4.12 latest
Re: Osc input not receiving
Posted: Tue Jun 28, 2022 8:55 am
by GGGss
Does your monitoring application run at the same time as QLC+? This is erroneous, since only one application can claim a network port.
Does the joystick wiggle when info is sent? If it does, you could create an input profile. If not, QLC+ does not listen to the network port... Verify with QLC+ running in a dos command prompt with this command: netstat -an. This should show you that port 7704 is present in the list (hence listening). Verify again with QLC+ __not__ running. The port should not be listed anymore.
Re: Osc input not receiving
Posted: Wed Jun 29, 2022 11:33 am
by SPS
GGGss wrote: ↑Tue Jun 28, 2022 8:55 am
Does your monitoring application run at the same time as QLC+? This is erroneous, since only one application can claim a network port.
Does the joystick wiggle when info is sent? If it does, you could create an input profile. If not, QLC+ does not listen to the network port... Verify with QLC+ running in a dos command prompt with this command: netstat -an. This should show you that port 7704 is present in the list (hence listening). Verify again with QLC+ __not__ running. The port should not be listed anymore.
Ok. I have the monitor app shutdown.
With my qlc project open and I run Netstat -an, The port 7704 is listed.
However, Netstat does not indicates: listening.
The line says: upd 127:0:0:1:7704 *:*
And no foreign address or State
With qlc not running, the port is not listed as you said.
What now.??
I also do not see a joystick in the universe line…..
Re: Osc input not receiving
Posted: Wed Jun 29, 2022 5:40 pm
by sbenejam
As a test, try to uncheck and check the input checkbox again.
Re: Osc input not receiving
Posted: Thu Jun 30, 2022 6:47 am
by GGGss
There is another thread dealing with qlc+ not listening to network packets, in the latest version.
So give it some time so @Massimo can pick this up also...
Re: Osc input not receiving
Posted: Thu Jun 30, 2022 1:38 pm
by SPS
sbenejam wrote: ↑Wed Jun 29, 2022 5:40 pm
As a test, try to uncheck and check the input checkbox again.
Thanks. Did it several times, but no luck
Re: Osc input not receiving
Posted: Thu Jun 30, 2022 1:40 pm
by SPS
GGGss wrote: ↑Thu Jun 30, 2022 6:47 am
There is another thread dealing with qlc+ not listening to network packets, in the latest version.
So give it some time so @Massimo can pick this up also...
thanks! I’ll wait for a solution.
Which thread is that you mean?
Paul
Re: Osc input not receiving
Posted: Fri Jul 01, 2022 7:38 am
by mcallegari
Yes, which thread?
Re: Osc input not receiving
Posted: Fri Jul 01, 2022 8:15 am
by GGGss
viewtopic.php?f=29&t=15642 - not related to OSC but smells network issues? No?
Re: Osc input not receiving
Posted: Fri Jul 01, 2022 8:33 am
by mcallegari
Not related. It's a specific OS2L protocol implementation issue
Can we see network traces (wireshark) of this thread issue?
Re: Osc input not receiving
Posted: Sat Jul 02, 2022 2:17 pm
by SPS
mcallegari wrote: ↑Fri Jul 01, 2022 8:33 am
Can we see network traces (wireshark) of this thread issue?
I ‘ll install wireshark and let You know the result.
Paul