If you read the Fixtures sharing guidelines and apparently you haven't, you will find out that gobos are a delicate matter as most of them are covered by copyrights.
In your fixtures you used gobo pictures you donwloaded from somewhere and moreover you used absolute paths pointing to your computer.
This is totally NOT OK when sharing a fixture. So I rejected them.
QLC+ comes with 870 bundled gobos. If you use them you are sure they are OK.
If you don't use them, I need the written permission of the gobo creator to include them in QLC+.
New Fixture
-
RODOLFO
Ok for the rights to the images even gobos though I doubt they are protected.
But if I understand, I must find the equivalent in the gobo image library supplied with the program?
But if I understand, I must find the equivalent in the gobo image library supplied with the program?
-
RODOLFO
Ok Ciao Massimo,
I noticed a problem with publishing an event bar fixture
Event bar 4 x 15w White Mode 9 channels ok each projector are the same movement. And with the Mode 28 channels the FX function uses the first Pan & Titl in the channels.
I solved the problem : I create a 7-channels mode and I use 4 X event bar fixture.
But if one day a projector using more motion, it will pose a problem to use the FX function.
I hope you understand the problem posed.
For example this one:
https://www2.highend.com/products/LED/s ... _C1_DS.pdf
I noticed a problem with publishing an event bar fixture
Event bar 4 x 15w White Mode 9 channels ok each projector are the same movement. And with the Mode 28 channels the FX function uses the first Pan & Titl in the channels.
I solved the problem : I create a 7-channels mode and I use 4 X event bar fixture.
But if one day a projector using more motion, it will pose a problem to use the FX function.
I hope you understand the problem posed.
For example this one:
https://www2.highend.com/products/LED/s ... _C1_DS.pdf
-
Jano Svitok
Rodolfo,
as for "multiple movement" fixtures: just add as many heads as needed and add related channels to the respective head (look at ADJ Event Bar definition for an example).
Event bar: create 4 heads, assing each group of 7 channels to one group.
I'd suggest that you name them Pan 2, Pan 3, Pan 4 etc. to make clearer to which group do they belong. Also I'd prefer English names, but that's me
For Shapeshifter: the issue is more difficult, there are two possibilities (I'm not sure if both work):
- create 6 heads, and assign related subpanel channels to each head, leaving global channels unassigned to any head (this may not work)
- create 7 head, assing global PAN/TILT channels to the first head and subpanel channels to heads 2..7 (alternatively, you can make the global head the last one).
This allows you to work with the fixture.
as for "multiple movement" fixtures: just add as many heads as needed and add related channels to the respective head (look at ADJ Event Bar definition for an example).
Event bar: create 4 heads, assing each group of 7 channels to one group.
I'd suggest that you name them Pan 2, Pan 3, Pan 4 etc. to make clearer to which group do they belong. Also I'd prefer English names, but that's me
For Shapeshifter: the issue is more difficult, there are two possibilities (I'm not sure if both work):
- create 6 heads, and assign related subpanel channels to each head, leaving global channels unassigned to any head (this may not work)
- create 7 head, assing global PAN/TILT channels to the first head and subpanel channels to heads 2..7 (alternatively, you can make the global head the last one).
This allows you to work with the fixture.
-
RODOLFO
Waht's Up with this Fixture Massimo ( Oh Uaglio ) ...
- Attachments
-
Laserworld-RS400G.qxf- (3.9 KiB) Downloaded 40 times
-
Boxy
Hi Rodolfo,
I've made a few changes according to the attached user manual. NOTE: Dot rotation has a missing range of missing DMX values (128-191). I don't have this device so can't check what these values do.
Regards,
Boxy
I've made a few changes according to the attached user manual. NOTE: Dot rotation has a missing range of missing DMX values (128-191). I don't have this device so can't check what these values do.
Regards,
Boxy
- Attachments
-
- Laserworld-RS400G.qxf
- (4.7 KiB) Downloaded 43 times
-
- Laserworld%2BManual%2B2011%2B-%2BRS%2B400%2BG.pdf
- (55.22 KiB) Downloaded 50 times
-
Massimo Callegari
This fixture is not good.
Author is wrong.
Channels are almost all dimmers. Give them a meaningful group.
Physical information is missing.
Mode name is wrong.
Author is wrong.
Channels are almost all dimmers. Give them a meaningful group.
Physical information is missing.
Mode name is wrong.