Hi,
I'm not sure if this is the official place to put these but I thought it might help some one.
Attached are two input profiles, one for the Novation Launchpad MK2 and the other for the Behringer X-Touch extender.
Input Profiles
-
OddSocks
- Posts: 152
- Joined: Tue Apr 14, 2015 11:33 am
- Real Name: Tim Cullingworth
- Attachments
-
Novation-LaunchpadMK2.qxi- (6.63 KiB) Downloaded 146 times
-
- Behringer-X-TouchExtender.qxi
- (6.3 KiB) Downloaded 99 times
-
siegmund
- Posts: 703
- Joined: Mon Nov 02, 2015 11:03 am
- Location: Germany
- Real Name: Lukas
Hey Tim,
there already have been some attempts on creating input profiles for Behringer X-Touch but afaik they were not successful - maybe you are willing to share your experiences?
www.qlcplus.org/forum/viewtopic.php?f=2 ... 43&p=47152
www.qlcplus.org/forum/viewtopic.php?f=2 ... 49&p=48937
there already have been some attempts on creating input profiles for Behringer X-Touch but afaik they were not successful - maybe you are willing to share your experiences?
www.qlcplus.org/forum/viewtopic.php?f=2 ... 43&p=47152
www.qlcplus.org/forum/viewtopic.php?f=2 ... 49&p=48937
-
OddSocks
- Posts: 152
- Joined: Tue Apr 14, 2015 11:33 am
- Real Name: Tim Cullingworth
Hi,
from what I can tell the three X-Touch units ( or maybe four with the X-Touch 1) are all quite different beasts.
I'm using the X-touch extender in Ctrl mode and every thing seems to work fine. The input profile is all correct.
Have not fully played with all the feed back but the faders certainly follow the feedback.
Having played with the encoders there is a bit of an issue as the led rings are separate from the encoder so there is no way to preset the value of the encoder with the feed back. So the encoder always starts at zero no matter what the feed back is. This would not be a problem if QLC could handle the relative mode for the encoders. In this mode you get a note velocity of 0 for a anticlockwise direction and a velocity of 65 for clockwise, but I can't work out how to helpfully use this.
One other thing I found was that to get the button leds to turn off I needed to set the off value to 1 rather than 0 and a value of 128 for flashing.
from what I can tell the three X-Touch units ( or maybe four with the X-Touch 1) are all quite different beasts.
I'm using the X-touch extender in Ctrl mode and every thing seems to work fine. The input profile is all correct.
Have not fully played with all the feed back but the faders certainly follow the feedback.
Having played with the encoders there is a bit of an issue as the led rings are separate from the encoder so there is no way to preset the value of the encoder with the feed back. So the encoder always starts at zero no matter what the feed back is. This would not be a problem if QLC could handle the relative mode for the encoders. In this mode you get a note velocity of 0 for a anticlockwise direction and a velocity of 65 for clockwise, but I can't work out how to helpfully use this.
One other thing I found was that to get the button leds to turn off I needed to set the off value to 1 rather than 0 and a value of 128 for flashing.
-
mcallegari
- Posts: 4711
- Joined: Sun Apr 12, 2015 9:09 am
- Location: Italy
- Real Name: Massimo Callegari
- Contact:
Profiles added !
Thanks a lot Tim
Thanks a lot Tim