No more audio devices in QLC+

Scully · Fri Aug 25, 2017 1:10 pm

Hi, I'm having a problem with the audio devices. I have 3 devices in Raspberry 3, but they do not show up in QLC +. The version is 4.11.0 GIT.

mcallegari · Fri Aug 25, 2017 2:43 pm

Which image are you using ?
That's clearly not my image. Please provide all the information if you want help

Scully · Fri Aug 25, 2017 3:02 pm

I have this version: qlcplus-qt5-git_4.11.0.20170507.dc48f42-0_armhf.deb. I sent a donation (15EU). I got a link to download the current version, but this version will not run at all. Fixture editor will show something, but it's also not working.

mcallegari · Fri Aug 25, 2017 3:37 pm

Again, you're not providing all the information needed:

1- where did you get that deb file ? That's not the name of the package I provide
2- which image are you using ? (Raspbian Wheezy, Jessie, Stretch, ??)
3- Which Qt version is installed in the image you're using ?
4-

I got a link to download the current version, but this version will not run at all.

What does this even mean ? What is not working ? What did you see ?

Scully · Fri Aug 25, 2017 4:00 pm

1. I downloaded from GIT source files and compile it (According to instructions from the web)
2. jessie 4.9.35-v7+
3.QT5
4.The QLC + version of the email will not display anything. I will run and nothing.

Thanks for your patience, I'm not a Linux expert.

Scully · Fri Aug 25, 2017 4:03 pm

Alternatively, you can connect through Teamviewer to the raspberry desktop.

mcallegari · Fri Aug 25, 2017 4:10 pm

Sorry but I can't give support to custom built versions. You say you're not a Linux expert but you built QLC+ from sources yourself...wow.
Qt5 is still too generic. There are like 20 versions out there.

My image has to work out of the box on a Raspberry Pi 3. If it doesn't then it means something went wrong when flashing it on the SD card. Are you sure you have properly followed the instructions ?
You should see at least the Pi boot splash screen (a colorful square on the TV) or the kernel boot messages.

Scully · Fri Aug 25, 2017 4:14 pm

I will try to reinstall raspberian, thanks so far.

Scully · Sat Aug 26, 2017 5:39 am

I installed jessie 4.4.50-v7 + (downloaded from the official raspberry site), I installed qlc + 4.11 from the email (donation). But qlc + will not run at all. What is the installation procedure for the new system installation? What do you need to install? I'm sorry for my ignorance, but I have not found any instructions. Do I need to install qt5 again? What version of raspbian qlc + is running on?

mcallegari · Sat Aug 26, 2017 10:41 am

What is the installation procedure for the new system installation?

Chapter 10 of the provided PDF

What do you need to install?

Chapter 10 of the provided PDF

I'm sorry for my ignorance, but I have not found any instructions.

Chapter 10 of the provided PDF

Do I need to install qt5 again?

Chapter 10 of the provided PDF. Yes.

What version of raspbian qlc + is running on?

Jessie. It's written here: http://www.qlcplus.org/raspberry.html, In chapter 2 of the provided PDF, and in the name of the PDF itself.

Dude, your issue is that you refuse to read the instructions.
Therefore, my help ends here, cause this is a waste of my time.

Scully · Mon Aug 28, 2017 5:10 am

Ah sorry, I did not look for a manual installation. Previously, just install the package. Now it's ok.